Contents hide
1Electric height adjustable desk manual
2Technical specifications
3 parts
4Installation instructions
5Install the lifting column
6Install the middle rail of the crossbar
7Install the table top and leg
8Install the Control Panel
9Install the cable management tray
10Troubleshooting
10.1 Protection and Warning
11Note
12Waste disposal
13FAQ
14WIDEO
15Documents / Resources
16 related posts
Electric height adjustable desk manual
Electric height adjustable desk manual
Technical Specifications
Height Range:610CM-1260CM(without desktop)Base width:1000MM-1800MMTravel speed:32 per second (no load)lifting capacity:Maks. 120 kgduty cycle:10%. Up to 2 minutes on, 18 minutes off : Soft start/stop : Adjustable leveling pins : 4 memory settings
Note / Information
- Make sure there are no obstacles in the way of the desk.
- Make sure the desktop is not touching any walls.
- Make sure all cables are the correct length to accommodate the change in height.
WARNING :Pinch point Keep hands and fingers away
- Keep children away from electric height adjustable desks, control units and headphones. There is a risk of injury and electric shock
- Keep all electrical components away from liquids.
- Do not sit or stand on the desk frame. Do not crawl or lie under the desk frame.
- Do not place objects taller than 20 inches under your desk.
- Do not open any components - legs, control box or switch. There is a risk of electric shock.
- This product is designed with a duty cycle of 10%. (2 mins on, 18 mins off)
Use/Liability
- This height-adjustable desk is equipped with electric motors and is intended for use in dry workplaces only.
- The height of the desk is adjustable, so you can set it to the most ergonomic height. Any other use is at the user's risk.
- Under no circumstances does the manufacturer accept any warranty claims or liability claims for damage caused by improper use or handling of the desk frame.
Important:Please read this manual carefully, if this desk is sold, give this manual to the buyer.
parts
Assembly instructions
Lay out all components and tools to ensure you have all the included parts listed on the previous page. Completely separate the ends of the crossbar. Inside you will find the middle crossbars.
Install the lifting column
- Insert one of the lifting columns to the end of the crossbar. Use a 5x5mm Allen key 4pcs M6*10 Thread the machine screws into the holes as shown.
- Using a 4x4mm Allen key, attach the side supports (5) to the end of the support beam. then thread 2pcs M6*40 machine screws.
But don't tighten them all the way. After installing all four screws, tighten them fully. Repeat steps 2-3 for the rest of the lifting column, crossbar tip, and side bracket.
Install the middle rail of the crossbar
Install the top and foot
Install the Control Panel
Install the cable management tray
Troubleshooting
Protection and warning
Block protection:when it displays "E02", it alarms when the desktop vibrates, collision and tilt, automatically clears the alarm when bounced; or press any key to clear the bounce alarm. Check and make sure the desk will not operate under high-amplitude vibration, barrier or tilt conditions, then try to restart.B. Overheat protection:when it displays "Hot", this protection may be activated after a long time, please wait at least 18 minutes before you can use it again. C. Motor failure protection: when "E10" is displayed, please check and make sure the connection between motor and controller is reliable, then turn off and on again or press reset to clear.D. Overload Protection:when it displays "E20", you need to remove some objects from the desktop when this occurs during the growth phase; or if it occurs during the drop phase, turn it off and on again or press reset to clear it.E. Undervoltage protection:when it displays "E31", it alarms when the supply voltage is lower than the limit value, please turn it off and on again to clear it. Otherwise, it can be auto cleared after it can be auto cleared after.F. Surge Protector:when it displays "E32", it alarms when the supply voltage is higher than the limit value, please turn it off and on again to clear it. Otherwise, it may be automatically cleared when the voltage reaches the set value.G. Protection beyond the step: when "E60" is displayed, please check and make sure that the motors of each channel are identical and their connection to the controller is reliable, then press reset to clear them.Note:Only a multi-motor system has over-step protection.
Attention
- Power supply: AC100V-240V,50/60Hz
- Working environment 0-40°C
- Unplug the plug before cleaning, wipe the dust on the surface with a slightly damp cloth when cleaning, be careful not to let the drops get into the internal parts, do not loosen the connector.
- The electrical box contains electronic components, metals, plastics, wires, etc., so it should be disposed of in accordance with the environmental regulations of each country, and not with general household waste.
- Please check carefully to ensure proper and complete assembly before use.
- Familiarize yourself with all features and program settings of the product before using it for the first time.
- It is forbidden for children to play with the product due to unforeseen actions during play, no dangerous consequences caused by this wrong action will not be on
- A little noise from the V-belt or brake system due to the design will not have any effect on the use of the equipment
- Corrosive or abrasive materials are prohibited to clean the equipment. He must ensure that the cleaning agent used does not pollute the environment.
- This appliance can be used by children from 8 years of age and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children must not play with the device.
- Cleaning and user maintenance must not be performed by children without supervision.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard.
- Make sure there are no sources of danger in your working environment. e.g. don't litter tools around. Always handle packaging materials with care to avoid potential hazards, e.g. a plastic bag may be a choking hazard for children.
- If necessary, keep the original packaging of the device for future transport use.
Waste disposal
This marking means that this product should not be disposed of with other household waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please recycle responsibly to promote a sustainable muse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling. Thank you for your attention!
Frequently asked questions
What is the difference between an electric height adjustable desk and a mechanical height adjustable desk?
The electric height adjustable desk uses an electric motor to adjust the height of the desk, which is more stable than the mechanical height adjustable desk.
What is the difference between an electric height adjustable desk and a hydraulic height adjustable desk?
The electric height adjustable desk uses an electric motor to adjust the height of the desk, which is more stable than the hydraulic height adjustable desk.
What is the difference between electrically adjustable desks and hydraulically adjustable desks?
Electrically adjustable standing desks use an electric motor to adjust the height of the desk, which is more stable than hydraulically adjustable standing desks.
How to lock the desk in a sitting position? He continues to slowly creep up to a standing position.
Check the exiter, go down to lock the position. Otherwise some problem with leaving
What is the lowest will go down to the floor? I'm short when I sit down and I have a child who would use it too.
The lowest is 28 1/2 inches. When looking at the item photo, you will see 6 boxes with small photos below the main image. When you click on the sixth image, the main image will display all the measurements.
Are the image measurements correct/incorrect? If you look at the pictures you can see that the top is 19″ and the side width is 23.5″, looks like the opposite?
The photo shows 25.8 x 19, right?
Do adjustable desks need to be plugged in?
Most motorized standing desks require an electrical outletfor raising and lowering the work surface.
Is it worth buying height-adjustable desks?
Standing desks are undoubtedly overrated, and most of the claimed benefits simply aren't true. While science is still catching up, existing research is definitely pointing in that directionstanding desks are simply not worth the investment.
Do electric standing desks break easily?
Electric height-adjustable desks are notorious for breaking down— their engines burn out and their electrical wires snap. Voltage issues can also cause your desk to simply stop working.
What are adjustable desks called?
That's where you'll find a height-adjustable standing desk (also known asstanding desk) comes in. You can quickly raise or lower the desk to alternate between sitting and standing throughout the working day, as recommended by our experts.
How long do electric desks last?
Continuing roughly from the table of 780 cycles per year, all tested RA Sit to Stand desks withstand a combined25,6 lat.
Better pneumatic or electric desk?
With fewer components than a motorized desk,the pneumatic system is simply more reliable. While electric desktop motors are known for motor burnout and failure, pneumatic desks require no maintenance or breakdown.
Is a standing desk better than sitting?
In addition to less sitting time, standing at work has other advantages:More calories burned: One study found that standing causes a loss of 88 calories per hour, compared to 80 calories while sitting. Walking burns a lot more - 210 calories per hour.
Are standing desks better for your back?
While a standing desk can ease back pain, it's probably not a cure-all. For example, a standing desk can help improve posture and take pressure off the neck and lower back; however, this is not enough to correct more serious problems such as scoliosis or disc herniation.
VIDEO
Documents / Resources
| Electric height adjustment Desk with electric height adjustment[pdf] User manual Desk with electric height adjustment |
related posts
Height Adjustable Computer Desk User Manual
Height Adjustable Computer Desk User Manual Safety Instructions Children must not operate this product without sufficient…
Y-Desk Electric Height Adjustable Desk Frame User Guide
Operating instructions for the Y-Desk desk frame with electric height adjustment Overview left leg 1 pc. right leg 1 pc. long tube 1 pc.…
CAMILLE desk manual
User manual for the CAMILLE desk User manual QC-CODE (for service requests) DISTRIBUTOR: BOPITA Energieweg 1, 6662…
- (Video) FlexiSpot EC1 Standing Desk Installation Guide
V I V Crank height adjustable desk manual
Crank Height Adjustable Desk Crank Height Adjustable Desk - Black User Manual SKU: DESK-M55TB Scan QR Code…
FAQs
Why is my electric standing desk not going down? ›
Unplug the desk from the power outlet and wait 30 seconds. Check all other cords for the desk's motor or control box and make sure they're secure. Plug the power cord into the wall socket. Press and hold the down arrow button (▼) until the table reaches its lowest position.
How do you manually lower an electric standing desk? ›Adjusting the height of standing desk converters is simple. To lower the desk, locate the handles on both undersides of the top section of the desk - this is usually where your monitors are placed. Once found, gently squeeze the handles and press down on the desk to lower it to your desired height.
What is the error code E01 on adjustable desk? ›E01 Leg Malfunction 1. Leg(s) are loose from the control box. Check cable connection, ensure legs are connected correctly.
Why won't my standing desk move up? ›This usually happens for one of two reasons: the desk was unplugged and then plugged back in, or the outlet lost power. When a standing desk loses power and then gets it again, it often goes into reset mode. A sit-stand desk can only move downwards while in reset mode.
How long do electric standing desks last? ›How Long Do Electric Standing Desks Last? Because it's electrical it's prone to more malfunctions and mishaps than mechanical desks. The chance of this happening is lower when you buy a quality product, as most electrical faults occur because of poor design. The lifespan of an electric desk ranges from 5- 10 years.
Can you manually raise a standing desk? ›A manual standing desk is a type of adjustable desk that does not use any type of powered mechanism to lift the desk surface up and down. Instead, the desk must be manually adjusted by the user, typically using a hand crank or lever to lift the desk surface to the desired height.
What is the error code E04 on a standing desk? ›E04: This error code will show if the legs are overloaded. Apart from too much weight on the desk, or over the top of one leg it may also be caused if one or all legs are not 90 degrees to the frame.
How do I reset my autonomous standing desk? ›- Unplug the desk for 20 seconds. Plug it back in. Wait a full 20 seconds.
- Press the up and down buttons until the desk lowers all the way and beeps or 20 seconds pass.
- Release both buttons.
- Press the down buttons until the desk beeps one more time or 20 seconds pass.
When looking specifically at the Economy Ryzer, if you get E01 or the E02 code, please allow the table to rest for 18 minutes before operating it again. If E03 or E04 codes show on the remote, the desk may be overloaded. Please lessen the load a confirm there is not more than 155lbs on the desk frame itself.
What is the E02 code on a standing desk? ›E01 or E02 Code shown on LED Display
This is is caused by overload of weight capticity (250 lbs +) or running the desk up and down continously over an extended period of time. Please unplug the desk, wait 20 minutes, and plug the desk back into power.
How do I get rid of E1 error? ›
Any boiler showing the E1 fault code means that a significant pressure drop has occurred in the system. The fix is to repressurise your boiler. When your boiler is switched off, the pressure gauge should read around 1 Bar – in the green zone on the gauge.
What is the error code eo8 on uplift desk? ›The "E08" error code on your hand control indicates an issue with the connection between your control box and the motorized legs.
What is error code E07 on uplift? ›E07 will display if the cable connected to the M1 port is not fully secured. Disconnect and reconnect the cable.
Why is only one side of my standing desk going up? ›Why only one side of my SmartDesk is raising? First, please check to see if the desk is connected to power, if the control box is still working, if the keypad is receiving power, and if the leg cables are not loosened. The working control box shows a green light if connected to power properly.
What does it mean when a standing desk is Loc? ›Desk Not Moving | Turning Child Lock On and Off
If you are seeing this error code or your desk is failing to move, it means, likely, your Child Lock is on.
They can cause a few problems: Leg and foot pain: Standing for long periods of time puts pressure on your knees, hips, and feet. This could lead to pain. If you lift one foot to ease the pressure, being off-balance could affect your posture.
Do electric standing desks break easily? ›Electric height-adjustable desks are notorious for breaking down — their motors burn out and their electrical wires break. Voltage issues can also cause the desk to simply stop working.
Is it OK to use a standing desk all day? ›Keep in mind that using a standing desk is like any other "intervention" — it can come with "side effects." For example, if you suddenly go from sitting all day to standing all day, you run the risk of developing back, leg, or foot pain; it's better to ease into it by starting with 30 to 60 minutes a day and gradually ...
How many hours a day should you stand at a standing desk? ›Try to alternate between sitting and standing every 30 to 60 minutes. Bottom Line: Try to alternate between sitting and standing. Early research suggests you should only spend 1 hour standing for every 1–2 hours sitting.
Can you stand too long at a standing desk? ›Risks of Standing For Too Long
Despite the proven benefits of standing desks, it seems you can also stand for too long. Ask anyone who is on their feet all day for work and most will tell you it isn't easy. Too much standing can cause lower back pain and problems with leg muscles, tendons and varicose veins.
How does a height adjustable desk work? ›
How does a Electric Desk Lift work? A Electric Desk Lift is powered by electric lifting columns that convert your desk into a standing desk. These columns replace the traditional stationary legs of your desk, and the control system will enable the user to adjust the desk's height.
What is E16 error on stand up desk? ›Message "E16" will flash on the screen for 5 to 10 seconds if the desk hits or has been hit by an object during operation. Please ensure you remove the object away from the desk then press the up or down button to adjust your desk height.
What is error code E12 on standing desk? ›error code E12 may indicate a fault with the Lifting Column plugged into channel 1 of the Control Box. To verify this, first disconnect power to the Control Box, and then swap the Lifting Column low-voltage connectors between channels 1 and 2, so that Lifting Column 1 is now plugged into 2, and 2 is plugged into 1.
What is the error code E00 on a standing desk? ›Error code E00
You have started a desk re-set and have abandoned it midway through. You need to continue resetting it . Unplug the desk from the mains for 10 mins. Re-plug it in, hold the up and down button simultaneously and do not let go.
This code means the desk needs to be reset. Please take use the following instructions described below when the LED display shows ASR. Please press AND CONTINUE TO HOLD the “▼” button until the desk reaches its lowest height and rebounds to stop to reset.
How do I fix ASR error on my standing desk? ›- Hold the DOWN button for about 3 seconds and then release it.
- The electric desk will lower down on its own and returns to a height.
- The ASR error will disappear on the LED panel display.
* E19: The reset process is interrupted. Please strictly follow the instruction to reset the system. Keeping pressing and hold the " Up " and " Down " buttons until the process is done.
How do I fix error code E02? ›If the water stops flowing as soon as you reconnect the filter (and you then get E02), it means the filter is the only thing obstructing water flow. To fix: - Replace the filters!
What is error code f05 e02? ›The F5 E2 alert indicates the washer can't engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area.
What is E1 E2 error codes? ›The E1 error code is an AUTO-STOP PROTECTION indicating a short or open circuit in the indoor pipe sensor. Try unplugging the unit and waiting 2 minutes for the power to discharge. Then plug the unit back in. The E2 error code is an AUTO-STOP PROTECTION indicating a short or open circuit in the indoor pipe sensor.
What does error code F8 E1 mean? ›
If F8 E1 or LF (too long to fill) appears in display, it means the washer is taking too long to fill. It's possible the drain hose extends more than 4.5" (114 mm) into standpipe. Check plumbing for correct drain hose installation.
What does error code F7 E1 mean? ›F7 E1 Code in display:
This code indicates a motor speed sensing error, the motor can not achieve the correct speed for the cycle selection.
E04: This error code will show if the legs are overloaded. Apart from too much weight on the desk, or over the top of one leg it may also be caused if one or all legs are not 90 degrees to the frame.
What is the step to change the row height in a table? ›- Select a row or a range of rows.
- On the Home tab, select Format > Row Width (or Row Height).
- Type the row width and select OK.
To set the row height to a specific measurement, click a cell in the row that you want to resize. On the Layout tab, in the Cell Size group, click in the Table Row Height box, and then specify the height you want.
What is resetting the table? ›Reset the Table aims to bring in new information, new themes, and new voices to find solutions to today's challenges.
What is the error code E02 on a standing desk? ›E01 or E02 Code shown on LED Display
This is is caused by overload of weight capticity (250 lbs +) or running the desk up and down continously over an extended period of time. Please unplug the desk, wait 20 minutes, and plug the desk back into power.
Alternatively called the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.